A Recent Visit to the ENVE Factory!

I wish I could say I were the one touring ENVE's factory, but the guys at Singletrack Magazine recently found their way over for a nice tour.  ENVE not only make killer forks and cockpit parts, but also makes many of the carbon tubes and lugs you'll find on US custom, hand-made bikes.  ENVE works directly with a number of builders to ensure that the perfect tube is chosen for each and every bike that builder makes.

Here are a couple of photos that stuck out to me, primarily because this is how my Independent Fabrication Cross Jester (cyclocross bike based on the Corvid road bike) was designed and constructed.  ENJOY!!

2012 Niner Jet9 RDO Medium Available!

These come in SO rarely for open stock, and for good reason: they are back-logged about 5 months!  With that said, this one was ordered for a customer though we were able to snag him one a few months ago, which puts this one available for purchase.  MSRP is $2599 with the custom-valved Fox RP23, but if you want to do a complete build we'll knock it out of the park for you.

Don't miss this one, Tang won't be around long!  If this were a large, it'd be mine.

2012 Felt F65x Gravel Grinder

Here's my new pride and joy set up as a road/gravel bike.  There's a ton of clearance front and rear for the "27c" Challenge Parigi-Roubaix tires, though mounted onto ENVE 29 XC rims the tire measures just a hair over 30mm.  One of my favorites about running disc brakes vs. cantilever when your bike is set up like this?  You don't have to be "that" guy showing up to a road ride with cantilever brakes!

What can I say about the new SRAM Red that I haven't said in previous posts?  It's really that good...

American Classic hubs have held up great so far, but with only a few hundred miles I would expect nothing else from them.  Engagement is a little slow compared to King or I9, but they sure are light!

ENVE rims have been spot on, but again only have a few hundred miles.  The internal nipples aren't my favorite since they require removal of the tire and rim tape to true, but I'm hoping a careful build with quality spokes will ensure they stay true for quite some time.

Clearance at the fork is huge even with a tire that measures over 30mm.  Of course, it should be since it's still had clearance with a Clement PDX mounted on a wide rim that was measuring 37mm.

Glamour shot from the rear.  The wheelset really sets this bike apart in my opinion, of course they retail for more than the stock complete bike so they should make a statement!

Hayes CX-5 still don't have a ton of miles on them, but have been a solid choice so far.  Performance is there, though the weight it a little high.  The weight can't be that big of a deal though since they weigh about the same as some Avid BB-7'.

Clearance in the rear is also massive.  Again, we'd expect nothing less since this is designed as a cyclocross bike with a fat smooth tire.

There she sits, I'm a fan.  More to come when the carbon version dubbed the F1x D finally arrives, which will hopefully be later this week.

On Test: Hayes CX-5 Mechanical Disc Brake Calipers

With the approach of cyclocross and disc brakes making their way to market, I started looking for options.  I'm not sure I'm ready to go to one of the converters on the market like the Hope V-Twin or TRP Parabox, maybe sometime soon, but not yet.

The Avid BB7 road and BB5 road are both fine, they really do their job well.  But they've been around for quite some time and have gone (mostly) without a challenger.  At the North American Handmade Bicycle Show this year, Independent Fabrication came in with a Ti Factory Lightweight disc cyclocross bike to show sporting the Hayes CX-5 mated to Shimano levers.

Mounting up the CX-5 was only slightly more difficult than the BB7, which is to say pretty darn easy.  Since you can adjust cable tension with the barrel adjuster as well as pad contact on the back side of the caliper all you really need to do is get them set up close initially and use the brake's own adjustments to dial them in.

Herein lies the major difference in setup between the BB7 and CX-5, the BB7 has a dial that's adjusted by hand where the CX-5 needs a 5mm allen.  Certainly not the end of the world, but I think it's noteworthy.

The first item of note when riding the CX-5 is how smooth they are.  The BB7 almost feels as though it has something dragging on the brake cable versus a Gore Sealed system for the CX-5.  The power isn't better on one than the other once the pads are broken in, so that's a wash.  I also wouldn't say modulation is any better with one than the other since they are both really quite nice.

My personal opinion is that the CX-5 looks a little nicer.  The silver polished finish with etched logos looks great and will match any gruppo well.  I think this brake on a Ti or stainless bike would be exceptional.

The stock BB7 I have in the store weighed in at 165g without hardware, the CX-5 came in at 190g without hardware.  The BB7 uses CPS washers from Avid that the CX-5 doesn't use, but I'd guess the BB7 would still weigh in a hair less.

The Future of Cyclocross is Disc?

After spending an entire summer longing for cyclocross season to come, I'm finally getting close.  This has been an interesting year too, with all of the new technology coming and the UCI now allowing disc wheels.

But this got me thinking, what's really the benefit of discs?  They aren't light, in fact they weigh quite a bit more.  I'd guess a disc wheel could resist sand buildup that a shallow rim could accumulate, but does that make up for the weight?

Let's get past the weight issue and move on to durability.  If a disc wheel can get a hole punched into it in a wheel bag, how is it supposed to stand up to a mass-start race where crashes are inevitable?  This one already has a hole in it, and the season hasn't even started!

And what's this about improved braking?  I don't claim to be a plastics expert, but this braking seems like it'll be the same as any other carbon wheel.  I've heard claims of better braking in adverse conditions, but I'm just not buying.

This particular disc does have dimples, but aerodynamics don't really matter in cyclocross.  The braking isn't going to be better on a disc wheel than any other carbon wheel.  Disc wheels are heavy.

After much thought I think I'm going to skip disc wheels for cyclocross.  I don't get all of the hype....

In Stock: Niner Carbon Jet9 RDO Tang Medium!

What happens when you want to race your Niner, but need full suspension? The Jet9 has been a solid choice, but was a little heavier than it's competition. That used to leave you with a choice to be made: do I suffer the extra weight or do I switch brands?

Well, if you've ever ridden any Niner products you'll know they have their geometry dialed. Why would you want to sacrifice the amazing CVA suspension design and geometry just for a little weight?

So let's say you've decided that the geometry and suspension is enough to keep you with Niner, but you're still struggling with the added heft of the Jet9 when compared to some of it's carbon-competition. Have no fear, because Niner has answered with the Jet9 RDO.

RDO stands for Race Day Optimized, a moniker that's being added to a number of items in the Niner line. It means you're getting equipment truly ready to be raced to your best times and right onto the podium!

Iron Cycles is one of the few spots in the country to find one of these frames. We have ONE brand new Jet9 RDO in medium coming in stock for sale. 


The Jet9 RDO is sporting a tapered head tube with inset headset. We've had a love affair with Chris King headsets for quite some time, and this machine screams for one! Tapered from 1-1/8" to 1.5" adds stiffness and steering precision.


Internal routing done very similar to the Air9 Carbon is a welcome addition, as long as you have a little patience. We've gotten pretty good at routing them, but if you're planning to build your own for the first time I recommend visiting www.ninerbikes.com and following their tutorial.


Fox RP23 with Kashima Coat. Does a rear shock get any better? Make it part of the patented CVA rear suspension design and know you've got the best rear suspension available.


A PressFit30 bottom bracket means tons of added stiffness for your pedaling pleasure! BB30 cranksets can be employed for lighter weight and a more narrow q-factor. Or, use a PF30 to BSA adapter and run a standard crankset.

Current wait time is roughly 4-5 months, unless you're ready for the one we have in stock. But don't wait, once this one is gone, you have a long wait for another....

In Stock: K-Edge Garmin Mount!

These things have been flying off of our shelves.  Our initial order was sold out in about 72 hours, but we have more arriving today!  Today's shipment includes gunmtal gray and red, more black mounts are coming but we're not sure when, probably another week.

Part of this shipment is already pre-sold and we're down to about 10 left.  Call today to get yours before they are gone again!

New Review: 2013 Felt F65x Disc Cyclocross Bike

You heard it here first, disc brakes are awesome for cyclocross.  OK, maybe not FIRST, but I've been pushing for disc since about 2008, but the frame and fork selection was lacking.  Currently components are catching on, but now they're behind the frames.  With many manufacturers rolling out brand new carbon CX frames this year to add to their current aluminum setups, and component manufacturers flashing a glimpse here and there of hydraulic setups, we know this is the way of the future.

For my first full-fledged attempt at disc CX I went with the Felt F65x.  Why?  It's the best thing that's readily available without going custom.  The frame is very similar to the F55x, so I know it'll handle well.  The geometry is dialed for me, so much so that my Independent Fabrication Cross Jester is based on the stock 57cm Felt cross bikes.

There's a lot going on with this build, so I'm going to take this in multiple entries.  First, let's cover the bike, we'll cover the pros and cons of the build next, and later cover the performance advantages and disadvantages.

The F65x isn't the lightest bike I've ever owned, but with alloy clinchers, disc brakes, alloy cockpit, a Quarq, 2012 SRAM Red, bottle cage, computer mount, and set up tubeless this bike still came in under 19lbs.  I assume a carbon equivalent with some light race wheels will come in around 17lbs, give or take.

The stock bike comes with a SRAM Apex/Rival build, Felt CX3R wheels, Avid BB5 brakes, and a nice SRAM S300 BB30 crankset.  The rear is spaced at 135mm, exactly what I think will be the de facto spacing.  The build is solid, and probably better than I would expect for a $1750 bike with such a nice frame.

The stock fork is a super-beefy Felt UHC model which offering some really great stiffness and a better than average ride quality.  Off-road the bike tracks very well, though when overgeared and sprinting on the road I am able to make the rotors rub the pads occasionally.  At some point down the road, I'll be giving the ENVE Disc CX fork a try.

Off the bat I clearly made a number of changes.  The 2012 SRAM Red is probably one of the first things many people will notice.  I'm smitten with it, but you can read my review on it here.  The addition of a Quarq was of course necessary since I'm numbers-driven, but it's a swap from my other bike anyway.  Seatpost became a Thomson because I just flat out trust their work.  The stem is currently a Zipp Service Course SL until a Thomson Elite X2 comes in, and the bars are Zipp SLC2 Short and Shallow which have been with me for 3 years and on countless bikes.

I kept the stock BB5 brakes on board, primarily because I forgot to bring the BB7's in when building the bike.  So far, the performance has been extraordinary.

Now let's talk about the wheel swap.  I wanted to keep this build "reasonable", other than the Quarq and Red of course.  I wanted to come up with a wheelset that can be put onto the stock bike and shed a nice chunk of weight, provide a huge performance benefit, and offer the best tubeless compatibility.  I've been using Stan's wheels since I started in mountain biking and have loved them ever since.  This year I managed to ruin a few sets of rims, but I'm chalking it up to bad luck.  From 2005-2011 I used either the 355 or Crest rim from Stan's with nary an issue.  In 2012 I ruined 5 total rims.  Bad luck or bad product?  I don't know, but since that bad streak I'm back to pure gold with them.

Here's the beauty of the stock Crest wheelset: for $530 you get a 1575g claimed (we've measured them to be far lower, but never higher) wheelset which shaves a full pound from the stock Felt CX3R wheelset.  The Crest internal rim width is 21mm vs the stock wheels roughly 17mm width, which means much better grip from your tires.  If you aren't familiar with why wide rims are better, check here.  The final HUGE bonus?  Tubeless compatibility. 

I'll cover the swap more in an upcoming post, but there is one positive that's coming close to being a negative: the wide rims have turned my Clement Crusade PDX 33 tires into a 37c monster!  The grip is out of this world from a knobby 37c CX tire, but clearance is an issue.  The fork is fine, tons of room.  The rear seatstays are begging a 40c tire, but the clearance around the chainstays is tight with a tire this big.

The driveside chainstay on the F65x with the 33c tires and Crest rims is about 5-7mm or so.  Clearance on the non-driveside chainstay is about 4mm or so.  I'm fine with the clearance on the driveside until it gets really nasty, but it's close on the non-driveside.  Of course, the bike comes stock with 32c tires on standard-width rims and offers ample clearance.  It's not until you really push into a tire that's measuring over 37mm that clearance is even something to look at.

There are a couple of solutions to this:

1. Ride away.  I gave the bike a few hard corners and a number of over-geared road sprints and never got the tire to rub.  The photos make it look slightly worse than it is, but so far it's been fine.
2. Run a 32c tire.  There are plenty out there, but the PDX is a favorite of mine.
3. Stan's probably has the best solution, the Iron Cross wheelset.  Coming in about a mm more narrow, I think that'll offer the breathing room to make me feel just fine about running this wheel/tire combo on this frame.  Plus, the name Iron Cross is just so damned good, you know!?

Tubeless setup with the Clement PDX, though not necessarily endorsed by Clement, was a breeze.  Literally, mount one side of the tire, toss some sealant in, mount the other side, inflate.  It was as fast as installing a tire with a tube.  Now you can run lower pressure without worrying about a pinch-flat, get better traction, and severely reduce the likelihood of a flat.

There you have it.  Disc CX is here and it's awesome.  Review on the performance from the brakes and the wheels are coming soon.  Until then, act now and get a disc CX bike.  Before you know it manufacturers will have tons of wheel options for tubeless and tubular, the brake options will be plenty, and you'll wonder why we didn't make the transition sooner.....damn you UCI!

Independent Fabrication Delux Redux

This is one I've been waiting on for a bit.  While I love following the technological advances in carbon happening now, not the least of which is the Felt Nine FRD I covered here, there's something so incredibly awesome about a retro-modern steel 29er.

After I met Gary Smith of IF, I became even more smitten with their bikes.  He was kind enough to help me out with getting me a Cross Jester last fall, has set us up with the first SSR Maxx available to the public, and an incredible Ti Factory Lightweight just to name a few.

But when Gary started teasing info on the Delux Redux I knew he was doing something a little different but a whole lot the same.  The details are just now rolling out in full, but a steel frame, an Ingleheart segmented fork, full Shimano XT, and handbuilt wheels by Luxe Wheelworks.  Go for El Fabuloso and you also get one-off purple anno Chris King parts!

Just a few of my favorite shots follow, but if you want one you'd better act fast.  These are limited to 12 of each color!

Clothing Sale!

We find ourselves with far too much 2012 clothing when we know 2013 clothing is coming soon.  Rather than end up with WAY too much in the store, we're going to equip you with the clothing you want now.  Help us help you, yeah, that's it!

Check it:

Don't wait too long.  The best sizes will go fast, don't miss out!  If you miss out, don't say we didn't tell ya.  'Cause we did.

This Just In: Felt's 2013 Road and Cyclocross Line Up!

Mountain bikes are fun, but they account for a tiny portion of the bikes we sell.  I love them, that's how I got my start into cycling, but being in a major metropolitan area with virtually no elevation gain, we'd go out of business focusing solely on mountain bikes.

Time trial and triathlon rigs are growing in our shop, we know them well but are just scratching the surface of what we can do with them for our customers.  Felt is killing it with their line-up, but again it's a relatively small fraction of what we do, though we do more with triathlon than we do with mountain bikes.

Which brings me to road bikes.  Road and cyclocross bikes are what we do.  Sure, we sell hybrids as well, and I think we understand them quite well, but road and cyclocross bikes are what we revolve around.

2013 is bringing a lot of new stuff to the Felt lineup.  The F-series line was brand new for 2012, so I didn't expect much of a change there, and we're primarily just seeing color and spec changes.  Much as expected since those bikes are so new and so good.

More importantly though, are the new Z-series bikes.  The carbon Z-series bikes were damn good already, but their technology was falling behind the incredible F-series and some of their competition.  So what did Felt do?  They made the new carbon Z-series bikes 50g lighter, 25% stiffer, yet more comfortable!  That's what I'm talkin' about.  They also made the carbon Z-series bikes natively electronic and mechanical transmission ready, added BB30, and gave the frames a tapered head tube for a tapered fork.

Here is the magical frame that I think people are going to love the second they ride it.  Felt knows carbon, and they've applied years of work to this frame.  Also, Felt has gone very subtle with colors this year which I am a HUGE fan of.  Though I believe this photo is of a prototype and not a stock color, you'll see what I mean in the next few photos

An image of that oversized head tube that's going to make this bike really shine.  Imagine a bike that when you stand up sprint just goes like a rocket, but also is smooth and comfortable enough to not beat you up when you hit a really bad stretch of road.

Another interesting shot of the head tube shows how far Felt has gone with their carbon mold to add ride quality while still retaining stiffness.

The Z4 will be a very popular bike for us sporting Shimano 105 and this beautiful color scheme.  Toned down is becoming very unique these days with so many brands kicking out bikes that have 12+ brand logos plastered all over the bike.

The AR-series also gets majorly refreshed for 2013.  While externally the bike remains virtually identical, internal changes net a loss of 350g (!!!!) while improving ride quality.  The weight of this frame was always the biggest detractor of it, but to drop nearly a full pound from the frame is shocking and should make this series much more appealing.  Even more, check out the paint scheme!  White with silver logos (only a couple of them) and a very small graphic.  Amazing if you ask me.

The AR does us a straight 1-1/8" steerer tube to maintain the best aerodynamics possible, whereas most of the other road bikes in Felt's lineup are now using tapered.

You've made it this far, you deserve some kudos.  And maybe a cookie.  Instead I'm giving you the Felt carbon disc CX bike.  This was shown in prototype form last year, but she'll be ready to race this fall.  Basically the F-series bike but with huge tire clearance and disc brakes.  This thing will be sweet!

The fork isn't new news to us since it's equipped on the F65x that we have in stock, but having it attached to a carbon frame is damned exciting!  I do have to say I've been surprised with the Ashima rotors so far.  In my experience light rotors are rarely round, but these have been great.

Rear dropouts were of course reworked for disc brakes, though not much.  Word has it that the current non-disc models were designed around disc brakes but cantilevers ended up being the go-to since so few road disc systems were available for 2012.

One feature I've loved since day 1 of the new F-series and the carbon cyclocross bikes is the ability to convert your frame from mechanical to internal electronic and back.  It literally takes about 90 seconds to change the cable stops to internal wiring and it integrates perfectly.

Tire clearance is huge on the disc bikes.  The last two seasons haven't seen much mud around here, but I have a sneaking suspicion that's going to change this season.  I'm picturing my disc carbon CX bike sporting some Clement PDX tubulars.  The perfect foul-weather CX bike.

There you have it, the info I have so far.  Much of the info was already there, but we hadn't received many pictures before the media day.  Luckily the guys at bikeradar.com are better photographers than I am anyway, so their pictures this time were worth what, about 1,000 words?

This Just In: Felt's 2013 Nine Line Up!

In 2005 I decided to give mountain biking a try.  I built my own bike for the experience, but within a handful of rides I realized the bike I built was too small.  When I started the search I was intrigued by 29ers, but at the time there just wasn't much available.  Tire selection was slim, wheel selection was slim, there were only a couple of forks out there to buy.  I made the plunge and picked up a Salsa, and from that day I've never gone back.

29ers offer the ability to roll over objects better than a 26er, they seem to fit me better at 6'1" because I feel like I am sitting "in" the bike rather than "on top" of it, they offer increased traction, etc etc.  But in the last 7 years 29ers have come a long way, rather than being a niche they now dominate the XC market in the midwest, and for good reason.  The frames have gotten lighter and stiffer, the geometry has been dialed to make 29ers more agile, component selection was exploded, the list goes on.

2010 brought a number of new models to market, the first one I was really excited about was the Niner Air9 Carbon.  It offered light weight, incredible stiffness, unmatched (even to today) drivetrain flexibility (single speed, BB30, PressFit30, GXP, BB90, etc), and all of the "new" mountain bike standards like a tapered steerer tube.

For 2012 Niner introduced the Air9 Carbon RDO which was a massaged version of the Air9 Carbon but shaved weight in a number of places for increased performance.

Felt saw what was happening in the market and for 2013 is not just meeting the expectations of XC racers everywhere but introducing a few new things as well.  The flagship Nine FRD frame comes in at a staggering $2900 but offers a claimed weight of 900g for the frame and utilizes TeXtreme carbon borrowed from Formula 1.

Felt was missing the boat with their previous Nine compared to the competition, even though it was a very nice frame.  It's a sell that the old frame didn't have a tapered steerer tube or oversized bottom bracket but still had a price tag rivaling the most expensive frames.

This new FRD frame, at 900g, is going to blow people away.  The best carbon money can buy, the best engineering available to our industry, and Felt has turned their F1 into a mountain bike.  This thing should be a rocket!

Niner carbon hard tail frames only gave me two real headaches: rear mud clearance and cable routing.  If Felt can nail the geometry Niner has gotten so good at, their new frame will kill Niner.  Felt's clearance around their tire is MASSIVE and comes without the "mud shelf" Niner carbon frames have.

Regarding cable routing, mechanics, wrap your head around this: fully lined and guided internal routing for front and rear derailleurs!  You riders may not care about this much, but when I spend an hour routing housing through an Air9 Carbon I tell myself I'll never do it again!  Let's hope this routing is as easy as Felt is making it sound!

I wish I could give you a first-hand ride report.  Our Felt rep said he spent some time on one and the new Nine was good enough to get him to forget he was riding a 29er, which is a huge compliment coming from a die-hard 26er rider.  It's only a matter of time before some of these new Nine frames and bikes are kicking around the store!

More info can be found here and here.